当前位置: 首页 > 协会标准 > ASTM 美国材料与试验协会 > ASTM D629-2008 纺织品定量分析的标准试验方法
ASTM D629-2008 纺织品定量分析的标准试验方法
世界资料网 / 2021-04-15
【英文标准名称】: Standard Test Methods for Quantitative Analysis of Textiles
【原文标准名称】: 纺织品定量分析的标准试验方法
【标准号】: ASTM D629-2008
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
【实施或试行日期】:
【发布单位】: 美国材料与试验协会(US-ASTM)
【起草单位】: D13.51
【标准类型】: (Test Method)
【标准水平】: ()
【中文主题词】:
【英文主题词】: Acceptance criteria/testing--textile fabrics/fibers; Animal fibers; Bast and leaf fibers/products; Cellulose and cellulose derivatives; Cellulose fiber; Chemical properties--textiles; Composition analysis--textiles; Cotton fibers; Cross-section measuremen
【摘要】: Test Methods D 629 for the determination of quantitative analysis of textiles may be used for acceptance testing of commercial shipments but caution is advised since information on between-laboratory precision is lacking. Comparative tests as directed in 5.1.1 or by Table D 1909 may be advisable. In case of a dispute arising from differences in reported test results using Test Methods D 629 for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens which are as homogeneous as possible and which are from a lot of material of the type in question. The test specimen should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student''s t-test and an acceptable probability level chosen by the two parties before the testing began. If a bias is found, either its cause must be found and corrected or the purchaser and supplier must agree to interpret future test results in the light of the known bias. The effects of the various reagents used in the chemical methods on the residual fibers in a blend depend upon the history of the fibers and, unless otherwise stated, are generally too small or too uncertain to warrant the application of correction factors. Fiber composition is generally expressed either on the oven-dry mass of the original sample or the oven-dry mass of the clean fiber after the removal of nonfibrous materials. If nonfibrous materials are not first removed from the textile before the fiber analysis is carried out, or if the treatments described in Section 8 are incapable of removing them, any such materials present will increase the percentage of the fiber constituent with which they are removed during the analysis, assuming they are soluble in the solvent used. The analytical methods are intended primarily for the separation of binary mixtures of fibers. These procedures may also be used for the analysis of mixtures containing more than two types of fibers by selecting the best combination of methods to use (Table 1). Since a sequence of solvents on a given fiber may produce different results than the expected results from a single solvent, it is advisable to determine the results of such sequential effects when testing multiple fiber blends. It is sometimes more convenient to separate mechanically the yarns in a textile which are of similar types, and then use the appropriate chemical method to analyze each of the components. Table 2 shows the solubilities of the various fibers in different chemical reagents.1.1 These test methods cover procedures for the determination of the fiber blend composition of mixtures of the fibers listed in 1.2. Procedures for quantitative estimation of the amount of moisture and certain nonfibrous materials in textiles are also described, for use in the analysis of mixtures, but these are not the primary methods for the determination of moisture content for commercial weights.
【中国标准分类号】: W55
【国际标准分类号】: 59_080_01
【页数】: 22P.;A4
【正文语种】: 英语

关键字: ASTM D629-2

相关资料

ASTM D629-2008 纺织品定量分析的标准试验方法
ASTM D629-2008 纺织品定量分析的标准试验方法
ASTM D6663-2008 单位和家用编织和针织盖被及附属品的标准规范
ASTM D1388-2008 织物硬度的标准试验方法
ASTM F2553-2008 用于彩弹游戏中适于再装的二氧化碳枪筒警告的标准规范
ASTM F2030-2008 彩弹球柱体防爆盘组件的标准规范
ASTM F2107-2008 棒球和垒球运动场带草皮区域的建造和维护用的标准指南
ASTM D7305-2008a 印刷品反射密度的标准试验方法
ASTM F2748-2008 低能量气枪(低于1 Joule)的标准规范
ASTM C1503-2008 镀银平镜的标准规范
ASTM F2710-2008 商业婴儿床的标准消费者安全性能规范
ASTM E1353-2008ae1 装饰性家具部件的耐香烟点燃性的标准试验方法
ASTM E2540-2008 用手持式逆反射测量仪在0.5度的观测角度测量反光标志的标准试验方法
ASTM E1006-2008 试验反应堆的物理放射量测定结果的分析和解释的标准实施规程,E 706(II)
ASTM E944-2008 反应堆监测时中子光谱调节法的应用的标准指南,E 706(IIA)
ASTM D6232-2008 废弃物和污染介质数据收集活动用取样设备选择的标准指南
ASTM E2552-2008 评估新型含能化合物对环境和人类健康影响的标准指南
ASTM D4188-2008 在线加压凝结-絮凝-过滤试验标准实施规程
ASTM D4193-2008 水中硫氰酸盐含量的标准试验方法
ASTM D2035-2008 水的凝聚絮凝瓶的标准试验
ASTM D5952-2008 军团菌的水系统检查和可能爆发军团病(军团病或庞蒂亚克热)调查的标准指南
ASTM C1345-2008 通过感应耦合等离子体度谱数对土壤中总的和同位素铀及总钍分析的标准试验方法
ASTM F1334-2008 测定真空吸尘器A-加重声音功率级的标准试验方法
ASTM D5462-2008 水中低水平溶解氧在线测量的标准试验方法
ASTM E1786-2008 在线红外分光光度法测定液氯中水的低等级的标准试验方法
ASTM D887-2008 水沉积物抽样的标准实施规程
ASTM D1245-2008 用化学显微镜作水沉积物的检验的标准实施规程
ASTM C1387-2008 土壤里锝99的测定的标准指南
ASTM D999-2008 集装箱振动测试的标准试验方法
ASTM D7459-2008 从固体燃烧物排放中收集源生物和化石二氧化碳排放的标准实施规程
ASTM F2327-2008 水中油检测和监测用空中远程感应系统的选择用标准指南
ASTM D4107-2008 饮用水中氚含量的试验方法

用户评论(共0条评论)

  • 暂时还没有任何用户评论
总计 0 个记录,共 1 页。 第一页 上一页 下一页 最末页
用户名: 匿名用户
E-mail:
评价等级:
评论内容: